Монголын Авто Форум

hi neg huselt bnaa zaluusaa Prius20d /xenon/ HID H4 bhaa teriig tavih gesiimaa + utas mutas holboltiig haana hideggiig medehgui bnaa bolomjtoi bol Hid gerel tavitsan P20 bwal zurag murgiig avaad ch yumuu eswel neeh goe tailbarlaad bicheed uguuch

ILoveGX110 wrote:hi neg huselt bnaa zaluusaa Prius20d /xenon/ HID H4 bhaa teriig tavih gesiimaa + utas mutas holboltiig haana hideggiig medehgui bnaa bolomjtoi bol Hid gerel tavitsan P20 bwal zurag murgiig avaad ch yumuu eswel neeh goe tailbarlaad bicheed uguuch

манай найз бид 2 хийсэн дээ. Урд байгаа гал хамгаалагчтай хайрцагнаас + авдын. Тэгээд - аас хаанаас ч хамаагүй авчих.

11 prius-ын удирдлагатай түлхүүрийг тааруулж болох уу? /удирдлагатай түлхүүр нь байхгүй байгаа зөвхөн запас түлхүүрээр ашиглаж байгаа/

Яг ориг юм шиг болгоно гэвэл задалсан приусын түлхүүр удирдлагыг ашиглах уу?

ajillana. tarulj bolno

Яг яасан нь дээрүү Заагаад өгөөч тэгүүл хийж үзмээр байна. Унасан приуснээс түлхүүрийг нь хүлээж авдаг юмтай нь /яг юу байдаг юм бол/ нь аваад өөрийхдөө хийнэ гэсэн үг үү

/хөгжимдөө forum-д байсан заавраар AUX гаралт хийсэн болж байна лээ/

HEDEN ONIIH BILE

2000 оных

http://www.programyourremote.com/classi ... cid=294-нд 2000 оных байдаггүй ээ

ЯАХУУ

1 oniih adilhansghde

1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Ochki wrote:1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Тэгээд одоо яг яах ёстой вэ? Яамар хамаагүй приусын удирдлагатай түлхүүр олоод энэ дээр байгаагаар таниулна гэсэн үг үү. /хэл муу/

tegne gsn ug. harin niit 5-s deesh tulhuur avdgui sanagdaad bn 3 ch bilu.

tgd bagtahgui bval ustgaj boldog bas neg adilavtar arga bdiin. uuruur helbel tulhuuree haychihval ustgana gesen ug.

buur bolohgui toyota computertei nuhduud deer ochijtaniulj bolno.

Ок tnks эхлээд нэг удирдлага олоод аваадахы тэгээд туршаад үзнээ

За өчигдөр орой муу тэргэндээ маш их баярлав хүлгийн тэнгэр хардаг л юм байна хэ хэ